Exhaust Wrap & Heat Protection

Exhaust Wraps: The truth about Wrapping

I can't tell you the number of calls I get from customers who are interested in DEI exhaust wrap but are afraid that the exhaust wrap may damage their pipes. Though a credible concern, I'm not sure who started the rumor about exhaust wrap, but for some people this myth has been inaccurately embedded as common knowledge to many. Wrapping pipes with our exhaust wrap will not damage your pipes.* It will not make the metal brittle or promote any enhanced corrosion. I've yet to see a picture of a header, turbo down pipe, or exhaust pipe that was damaged by exhaust wrap as one would think that with all the information and images available on the internet someone would have been able to provide proof of such negative occurrences. I was really shocked after reading several forum threads from the "self-proclaimed know-it-alls" that consistently post replies in response to inquiries from other members citing a story or rumor rather than from personal experience.

THE TRUTH
Basically, every time you start up an engine the exhaust system pipes heat up and undergo an aging process that is so nominal it would take 50+ years to actually see any kind of change in the metals composition. Exhaust wrap does accelerate this aging process, but even so it could take up to 30+ years using exhaust wrap to see any real degradation of the metal "AND" even that would be nominal at best! The same applies to ceramic jet coatings so don't let anyone tell you otherwise (that it's better because it doesn't make a difference).

*NOTE
In rare instances rust and corrosion may occur on lower grade metals so be sure to use DEI HT Silicone Coating with your exhaust wrap to repel water and debris).

As with any product, DEI has made available product FAQ and Instruction sheets online in PDF format.

Aluminized & Reflective Materials	Spark Plug Protection	Tapes & Sleeves

	BOOM MAT Performance Acoustical Material - 12-1/2`` x 24`` Sheet (10 pack)  Item #: 050210  $135.95 Boom Mat is a simple and effective solution in eliminating squeaks, rattles, vibrations and unwanted engine and road noise. Constructed of a rubber-based (viscoelastic) polymer layer with an aluminum foil laminate outer facing, Boom Mat's strong adhesive backing is unaffected by extreme hot and cold temperatures, is corrosion resistant and can be applied to metals, painted areas, plastic, fiberglass, automotive coatings and difficult to bond surfaces to name a few. With an ultra strong adhesive backing it can be applied in horizontal, vertical and inverted applications as well as on complex shapes. In addition to being a superior sound absorber and a solution in controlling vibration over a wide temperature range, Boom Mat is also an excellent thermal insulator. Capable of damping annoying low frequency noise, Boom Mat also serves as a barrier to unwanted mid and high frequencies.
	BOOM MAT Performance Acoustical Material - 12-1/2`` x 24`` Sheet (20 pack)  Item #: 050212  $265.95 Boom Mat is a simple and effective solution in eliminating squeaks, rattles, vibrations and unwanted engine and road noise. Constructed of a rubber-based (viscoelastic) polymer layer with an aluminum foil laminate outer facing, Boom Mat's strong adhesive backing is unaffected by extreme hot and cold temperatures, is corrosion resistant and can be applied to metals, painted areas, plastic, fiberglass, automotive coatings and difficult to bond surfaces to name a few. With an ultra strong adhesive backing it can be applied in horizontal, vertical and inverted applications as well as on complex shapes. In addition to being a superior sound absorber and a solution in controlling vibration over a wide temperature range, Boom Mat is also an excellent thermal insulator. Capable of damping annoying low frequency noise, Boom Mat also serves as a barrier to unwanted mid and high frequencies.
	BOOM MAT Performance Acoustical Material - 12-1/2`` x 24`` Sheet (6 pack)  Item #: 050206  $87.95 Boom Mat is a simple and effective solution in eliminating squeaks, rattles, vibrations and unwanted engine and road noise. Constructed of a rubber-based (viscoelastic) polymer layer with an aluminum foil laminate outer facing, Boom Mat's strong adhesive backing is unaffected by extreme hot and cold temperatures, is corrosion resistant and can be applied to metals, painted areas, plastic, fiberglass, automotive coatings and difficult to bond surfaces to name a few. With an ultra strong adhesive backing it can be applied in horizontal, vertical and inverted applications as well as on complex shapes. In addition to being a superior sound absorber and a solution in controlling vibration over a wide temperature range, Boom Mat is also an excellent thermal insulator. Capable of damping annoying low frequency noise, Boom Mat also serves as a barrier to unwanted mid and high frequencies.
	BOOM MAT Performance Acoustical Material - 12`` x 12 1/2`` Sheet (2 pack)  Item #: 050200  $22.95 Boom Mat is a simple and effective solution in eliminating squeaks, rattles, vibrations and unwanted engine and road noise. Constructed of a rubber-based (viscoelastic) polymer layer with an aluminum foil laminate outer facing, Boom Mat's strong adhesive backing is unaffected by extreme hot and cold temperatures, is corrosion resistant and can be applied to metals, painted areas, plastic, fiberglass, automotive coatings and difficult to bond surfaces to name a few. With an ultra strong adhesive backing it can be applied in horizontal, vertical and inverted applications as well as on complex shapes. In addition to being a superior sound absorber and a solution in controlling vibration over a wide temperature range, Boom Mat is also an excellent thermal insulator. Capable of damping annoying low frequency noise, Boom Mat also serves as a barrier to unwanted mid and high frequencies.
	BOOM MAT Performance Acoustical Material - 12`` x 12 1/2`` Sheet (4 pack)  Item #: 050202  $32.95 Boom Mat is a simple and effective solution in eliminating squeaks, rattles, vibrations and unwanted engine and road noise. Constructed of a rubber-based (viscoelastic) polymer layer with an aluminum foil laminate outer facing, Boom Mat's strong adhesive backing is unaffected by extreme hot and cold temperatures, is corrosion resistant and can be applied to metals, painted areas, plastic, fiberglass, automotive coatings and difficult to bond surfaces to name a few. With an ultra strong adhesive backing it can be applied in horizontal, vertical and inverted applications as well as on complex shapes. In addition to being a superior sound absorber and a solution in controlling vibration over a wide temperature range, Boom Mat is also an excellent thermal insulator. Capable of damping annoying low frequency noise, Boom Mat also serves as a barrier to unwanted mid and high frequencies.
	BOOM MAT Performance Acoustical Material - 12`` x 12 1/2`` Sheet (8 pack)  Item #: 050204  $57.95 Boom Mat is a simple and effective solution in eliminating squeaks, rattles, vibrations and unwanted engine and road noise. Constructed of a rubber-based (viscoelastic) polymer layer with an aluminum foil laminate outer facing, Boom Mat's strong adhesive backing is unaffected by extreme hot and cold temperatures, is corrosion resistant and can be applied to metals, painted areas, plastic, fiberglass, automotive coatings and difficult to bond surfaces to name a few. With an ultra strong adhesive backing it can be applied in horizontal, vertical and inverted applications as well as on complex shapes. In addition to being a superior sound absorber and a solution in controlling vibration over a wide temperature range, Boom Mat is also an excellent thermal insulator. Capable of damping annoying low frequency noise, Boom Mat also serves as a barrier to unwanted mid and high frequencies.
	BOOM MAT Performance Acoustical Material - Spray-on (18 oz. can)  Item #: 050220  $14.95 Boom Mat Spray-On is an effective solution in eliminating squeaks, rattles, vibrations and unwanted engine and road noise. Eliminates road noise Dampens vibrations For hard to reach areas For interior and exterior Covers 20 square feet Dries to touch in 20 minutes Helps prevent rust
	Cool-Tape Plus TM 2`` x 60`  Item #: 010413  $66.98 Cool-Tape consists of a 1 mil aluminized material bonded to a light weight, woven fiberglass with super strong adhesive backing and release liner. Cool-Tape can reflect up to 1500 degrees of radiant heat. The uses are limited only by your imagination but common uses include wrapping wires or fuel lines and sealing openings in floor boards or firewalls. This is the finest heat shielding tape on the market Up to 1500 degree protection More flexible Strong adhesive Thin for a tight wrap
	Cool-Tape TM 1-3/8`` x 15`  Item #: 010408  $21.38 Cool-Tape consists of a 1 mil aluminized material bonded to a light weight, woven fiberglass with super strong adhesive backing and release liner. Cool-Tape can reflect up to 1500 degrees of radiant heat. The uses are limited only by your imagination but common uses include wrapping wires or fuel lines and sealing openings in floor boards or firewalls. This is the finest heat shielding tape on the market Up to 1500 degree protection More flexible Strong adhesive Thin for a tight wrap
	Cool-Tape TM 1-3/8`` x 30`  Item #: 010416  $37.99 Cool-Tape consists of a 1 mil aluminized material bonded to a light weight, woven fiberglass with super strong adhesive backing and release liner. Cool-Tape can reflect up to 1500 degrees of radiant heat. The uses are limited only by your imagination but common uses include wrapping wires or fuel lines and sealing openings in floor boards or firewalls. This is the finest heat shielding tape on the market Up to 1500 degree protection More flexible Strong adhesive Thin for a tight wrap
	Dyno Strap Heat Guard (36`` long x 5`` wide)  Item #: 010466  $46.01 Keep your Dyno Straps from burning through and letting the car go flying in a wall! This product offers burn-through protection for dyno tie-down straps. Made of a high-temperature resistant aluminized mylar material, the Dyno Strap Heat Guard will withstand 500°F direct heat and 2000°F of radiant heat. It measures 5” wide by 3 feet and easily slips over dyno tie-down ends and slides over strap to be positioned near the area where exhaust heat exits. Protect dynamometer tie-down straps from burn-through from exhaust exit heat Made of hi-temp resistant aluminized material Withstands500°F direct / 2000°F radiant heat Easily slips over dyno tie-down strap Adjust to desired location near source of exiting exhaust 36” long x 5” wide
	Heat Resistant Sealant, 3 oz. Tube  Item #: 010410  $21.77 This is the best product to install our Heat Screen (above), but the uses are limitless. Anytime you need to bond or seal around heat this is the product for you. Dow Corning developed this product for the extreme conditions faced by the aerospace industry. Use on fiberglass, metal, wood, rubber & plastic Peel strength of 20 lbs. Performs continuously at V85 to 500 degrees F.
	Heavy Duty Spray Adhesive  Item #: 12005  $24.95 Thermo-Tec's new Heavy-Duty Spray Adhesive is perfect for use with these Thermo-Tec products - new Thermo-Guard FR, the Cool-It Insulating Mat and the Aluminized Heat Barrier, but you don't have to limit its use to these products! Heavy-Duty Spray Adhesive is a fast-drying, quick-bonding, high temperature contact adhesive. Use it wherever you need a secure, long-lasting, easy-to-apply bond. It is available in a generous 16.75 oz. can.
	Hi-Temp Spray Adhesive  Item #: 010490  $21.95 Ideal for automotive and marine headliners, trim and laminating, Hi-Temp Spray Adhesive is formulated to bond substrates that require either high bond strength and/or needs elevated temperature resistance. Hi-Temp Spray Adhesive provides high strength adhesion and bonds a wide variety of materials, including foams, fabrics, vinyl, wood, plastics and more. It has a specially designed three-way adjustable valve allowing the user to select the spray pattern that best suits the job. This multipurpose adhesive dries quickly and clear while forming a water-resistant bond. 10 oz can
	HT Silicone Coating - Aluminum  Item #: 010302  $14.95 The HT Silicone Coating provides lasting protection for any hot surface up to 1500 degrees. We recommend the use of this coating with our exhaust wraps because it seals the material and provides lasting protection from oil, dirt and road grime. Don't limit the use to exhaust header wrap, this products works well on headers, blocks, starters and even on your grill at home. Heat protection up to 1500 degrees Seals and protects exhaust wrap Many uses around the home and shop One can enough for V-8 headers
	HT Silicone Coating - Black  Item #: 010301  $14.95 The HT Silicone Coating provides lasting protection for any hot surface up to 1500 degrees. We recommend the use of this coating with our exhaust wraps because it seals the material and provides lasting protection from oil, dirt and road grime. Don't limit the use to exhaust header wrap, this products works well on headers, blocks, starters and even on your grill at home. Heat protection up to 1500 degrees Seals and protects exhaust wrap Many uses around the home and shop One can enough for V-8 headers
	HT Silicone Coating - White  Item #: 010303  $14.95 White HT Silicone Coating joins the popular selling Black and Aluminum premium high temp spray. The silicone additive penetrates and helps seal exhaust wrap while protecting against abrasions, hot oil spills, grease and road grime. In addition, HT Silicone provides protection from extreme heat that can potentially damage exhaust wrap while prolonging the lifespan of the wrap. HT Silicone Coating also has multiple uses around the home or shop. It's perfect for engine blocks, headers and even outdoor grills.
	HT Silicone Coating Assortment Case (6 Cans)  Item #: 010300  $57.95 Contains two cans of each HT Silicone Coating: White, Black & Aluminum White HT Silicone Coating joins the popular selling Black and Aluminum premium high temp spray. The silicone additive penetrates and helps seal exhaust wrap while protecting against abrasions, hot oil spills, grease and road grime. In addition, HT Silicone provides protection from extreme heat that can potentially damage exhaust wrap while prolonging the lifespan of the wrap. HT Silicone Coating also has multiple uses around the home or shop. It's perfect for engine blocks, headers and even outdoor grills.
	T3 Titanium Turbo Shield  Item #: 010140  $230.48 Design Engineering's custom-fit T3 Titanium Turbo Shield with LR Technology provides the ultimate means of reducing turbo lag while serving as a superior heat barrier, shielding and protecting engine components, hoods and painted surfaces. Made from pulverized lava rock, the T3 Titanium Turbo Shield can withstand can withstand 1800°F of direct heat thus reducing underhood temperatures. The result - cooler air intake temperatures for improved performance and a boost in horsepower.
	T3 Titanium Turbo Shield Kit  Item #: 010141  $251.76 Design Engineering's custom-fit T3 Titanium Turbo Shield with LR Technology provides the ultimate means of reducing turbo lag while serving as a superior heat barrier, shielding and protecting engine components, hoods and painted surfaces. Made from pulverized lava rock, the T3 Titanium Turbo Shield can withstand can withstand 1800°F of direct heat thus reducing underhood temperatures. The result - cooler air intake temperatures for improved performance and a boost in horsepower. Each T3 Titanium Shield kit includes: Shield, 2" x 15 ft roll of Titanium Wrap, two 14" stainless steel T3 Turbo Shield Only zip ties and 5 ft of fastening wire.
	TARGA EXHAUST HEAT SHIELD - BLACK  Item #: 18-500BK  $54.93 These anodized aluminum shields are designed to eliminate burning your boots or shoes on the hot mid-pipe, reduce marks on your pipe and add a performance look to your bike. Fits 2" to 2 5/8" dia. pipes on most stock and aftermarket systems. The 7" length offers maximum protection. The lightning/cooling holes are radiused to reduce boot scuffing and abrasions. Easy installation with the 2 stainless steel clamps provided. SOLD INDIVIDUALLY. For dual exhaust systems, order quantity two (2) units. Fits: ALL SPORTBIKES
	TARGA EXHAUST HEAT SHIELD - BLUE  Item #: 18-500BL  $54.93 These anodized aluminum shields are designed to eliminate burning your boots or shoes on the hot mid-pipe, reduce marks on your pipe and add a performance look to your bike. Fits 2" to 2 5/8" dia. pipes on most stock and aftermarket systems. The 7" length offers maximum protection. The lightning/cooling holes are radiused to reduce boot scuffing and abrasions. Easy installation with the 2 stainless steel clamps provided. SOLD INDIVIDUALLY. For dual exhaust systems, order quantity two (2) units. Fits: ALL SPORTBIKES
	TARGA EXHAUST HEAT SHIELD - GOLD  Item #: 18-500G  $54.93 These anodized aluminum shields are designed to eliminate burning your boots or shoes on the hot mid-pipe, reduce marks on your pipe and add a performance look to your bike. Fits 2" to 2 5/8" dia. pipes on most stock and aftermarket systems. The 7" length offers maximum protection. The lightning/cooling holes are radiused to reduce boot scuffing and abrasions. Easy installation with the 2 stainless steel clamps provided. SOLD INDIVIDUALLY. For dual exhaust systems, order quantity two (2) units. Fits: ALL SPORTBIKES
	TARGA EXHAUST HEAT SHIELD - RED  Item #: 18-500R  $54.93 These anodized aluminum shields are designed to eliminate burning your boots or shoes on the hot mid-pipe, reduce marks on your pipe and add a performance look to your bike. Fits 2" to 2 5/8" dia. pipes on most stock and aftermarket systems. The 7" length offers maximum protection. The lightning/cooling holes are radiused to reduce boot scuffing and abrasions. Easy installation with the 2 stainless steel clamps provided. SOLD INDIVIDUALLY. For dual exhaust systems, order quantity two (2) units. Fits: ALL SPORTBIKES
	TARGA EXHAUST HEAT SHIELD - SILVER  Item #: 18-500SL  $54.93 These anodized aluminum shields are designed to eliminate burning your boots or shoes on the hot mid-pipe, reduce marks on your pipe and add a performance look to your bike. Fits 2" to 2 5/8" dia. pipes on most stock and aftermarket systems. The 7" length offers maximum protection. The lightning/cooling holes are radiused to reduce boot scuffing and abrasions. Easy installation with the 2 stainless steel clamps provided. SOLD INDIVIDUALLY. For dual exhaust systems, order quantity two (2) units. Fits: ALL SPORTBIKES

Customer Service: Service@1Cruiser.com   720-445-5383