|
| HT Silicone Coating - Aluminum |
The HT Silicone Coating provides lasting protection for any hot surface up to 1500 degrees. We recommend the use of this coating with our exhaust wraps because it seals the material and provides lasting protection from oil, dirt and road grime. Don't limit the use to exhaust header wrap, this products works well on headers, blocks, starters and even on your grill at home. Heat protection up to 1500 degreesSeals and protects exhaust wrap Many uses around the home and shop One can enough for V-8 headers
|
| |
| This item usually takes about 7 days to ship |
| |
| Item no. 010302 |
| Today's Sale Price: $14.95 |
|
|
|
|
|
|
|
|
|
|
|
|
| This item does NOT ship for free |
| Shipping charges will apply to this item. If you place your order now we will call with the shipping rate. If the rate is approved by you we will charge you the additional shipping. If the rate is NOT approved by you then we will cancel your order. If you do not wish to place your order now you can enter in the quantity you wish to order and your zip code in the Q&A section below and we will respond with a quote. |
|
|
|
DEI High-Temp Silicone Coating FAQ
What is the purpose of using HT Silicone Coating?
HT Silicone Coating has several beneficial purposes on header wraps and metal surfaces. When applied to an exhaust wrap it increases the wraps thermal isolation and resistance. The silicone agent bonds to the surface of the wrap and increases its integrity which reduces the need to re-wrap headers or piping, just re-apply HT Silicone Coating routinely. HT Silicone can also be applied to a prepped metal surface where wrapping is improbable. Because HT Silicone Coating is silicone based it also can repell water, dirt and oils from any surface. This is especially usefull on header wrap as keeping it free of debris lessens wear and increases it's durability.
What else can HT Silicone Coating be used for?
Wherever metal heat absorbtion may exist! The intended use for this product is on header wrap as mentioned above, but HT Silicone Coating may also be applied to bare metal headers, exhaust pipes, manifolds, engine blocks, heads, valve covers, oil pans, transmission or rear-end housings, differential covers, brake calipers and even on your barbeque grill.
What temperature can HT Silicone Coating withstand?
HT Silicone Coating will effectively withstanding 1500 degees and provide added style.
How is HT Silicone Coating applied?
For header wraps it is recommended that HT Silicone be applied in several light coats for optimal thermal performance and cleanliness. For bare metal surfaces it is recommended that the surfaces be properly prepared before applying.
|
|
|
| WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations. |
|
| The Q&A on this Product |
|
|
| QUESTION: Would this stuff be good for heat treating the underside of a set of fabric saddlebags for a motorcycle? |
| ANSWER: This is not the ideal product for the purpose of protecting saddlebags. It is for sealing the absorbent material of exhaust heat wrap against moisture to ensure long service life. Only an air gap and heat wrap will save your saddle bags and their contents. Please order the product you need from 1Tail.com, not 1Trail.com - it will assist in expediting your order. |
|
| QUESTION: could you ship two cans of the aluminum HT silicone coating to Aguadilla, Puerto Rico 00605? |
| ANSWER: Certainly. We ship to Puerto Rico by USPS Priority Mail. |
|
| QUESTION: Can I use it with plastic intake manifold or any plastic inside the car like air filter housing to reduce the haet from the exhaust pipe? |
| ANSWER: This is for use on the exhaust pipe itself, not the plastic. You put it on the hot item and more heat will go out the back of the pipe - less heat will reach your plastic parts. You could wrap the plastic parts in one of the radiant barrier materials in addition. |
|
|
|
| Ask your question here: |
|
| Your email (so we can send you the answer): |
|
|
|
Event Photos
powered by WordPress e-commerce company