|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Can’t find a matching part number? Find the piston size of your unit. Front Master Cylinders - check the top or bottom of the lever clevis for a stamped alphanumeric string. The last two digits in the string indicate the piston size in mm (EXAMPLE: ‘1PJK 15’ = 15mm piston. In the case of ‘Radial-GP’ pumps, you may see a ‘PR’ or ‘/’’ stamping, followed by a number. If the number is “19x18” or “16x18”, the first number is piston size, the second refers to the pivot centers of the unit’s lever). Rear Master Cylinders - for lever-types, check clevis area as above. If rod-actuated, check the entire body for the alphanumeric string or a string starting with ‘PS’ (EXAMPLE: ‘PS12’ = 12mm piston). |
|
|
| WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations. |
|
| The Q&A on this Product |
|
|
| QUESTION: Hi , is there rebuild kit for Brembo clutch master 10.5800.10 ? thank you. |
| ANSWER: No, you will need to sent it to Brembo racing for repairs or replace it.
|
|
| QUESTION: Hi, I'd like to know if the part #'s (10.5800.10) & (10.4760.85) make a match set (as far as color goes).. I make high-end custom motorcycles and this factor is crucial. If they are, what color are they and what is the availability on them. Thank you.
Wayne Ransom
|
| ANSWER: The 10.5800.10 is a billet unit and the 10.4760.85 is a forged unit. I cannot gaurantee that the color will match. I reccommend that you use the NEW RCS Units. They do match. I will not have them available for about 4 more weeks.
Thank You,
Jolene |
|
| QUESTION: and also im looking for a new clutch for my 1996 gsxr 750 and i cant seem to find it on your wedsite....am i just not looking in the right place? appreciate the help
drew |
| ANSWER: YOu should wait a few weeks and get the new unit for the clutch. It is the new RCS unit and will be fully adjustable and better than the 10.5800.10. It iwll be on our website soon.
|
|
| QUESTION: do you have the unbreakable brembo clutch levers for a 250 sxf KTM 2007 and what is the cost? |
| ANSWER: There are a few different sizes lf folding levers.
One for a 20mm pivot, one for an 18mm pivot and one for 18mm in a shorter lever.
Depends on what length you want. |
|
| QUESTION: hello:) is there a brake light switch on this master cylinder? |
| ANSWER: This is a clutch part number and No! |
|
| QUESTION: I don't know which lever suits this radial pumps that I am interested in? |
| ANSWER: Part number 110.4594.61. |
|
| QUESTION: Is this a forged master cyl? Any different from a 18/19 radial brembo master cyl other than Looks? Do you have the brake switch? |
| ANSWER: The 10.5800.10 is a billet unit. Brembo doesn't make the hydraulic switch anymore. |
|
| QUESTION: Hi I have replaced my Master Slave cylinder with an Evolzione, but I'm still getting air into the system. I believe the only other place it could be is at the clutch resivoir. Can you give me the part number and cost to send one to New Zealand. For a 2004 Ducati 999. Regards Jason McLachlan |
| ANSWER: Your part number for a new cluth cylinder is 10.8101.10 at $235.97. Freight would be about $35.00. Thank You,
Jolene |
|
| QUESTION: What is the product called for the adjustement cable/knob that resides on the left handlebar pertch that I believe enables you to adjust the feel of your front brake lever "on-the-fly". Can you tell me anything about this? I didn't get a fulll answer before. Thank you! Tom |
| ANSWER: It is called a remote adjuster. It is only a cable with a rubber hose covering the cable. If you need more information email Jason at Brembo he is more familiar with the item. His email is jhiliker@brembo.com.
Thanks,Jolene |
|
| QUESTION: Hello!
I want to learn more about a adjuster that I have seen commonly on AMA and MotoGP race bikes. Its an adjustement cable/knob that resides on the left handlebar pertch that I believe enables you to adjust the feel of your front brake lever "on-the-fly".
Can you tell me anything about this? Where can I get one? Learn more?
Thank you!
Tom
|
| ANSWER: Order on from me! I have them in stock. $225.35 is the price. |
|
| QUESTION: Hi there,
looking to order some brembo parts and am checking availability and
shipping timing:
Brembo radial clutch: 10.5800.10
Brembo radial brake: 10.4760.70
Mirror clamp LH: 110.4372.16
Mirror clamp RH: 110.4372.13
Thanks you for your time
Best regards
simon |
| ANSWER: Hi Simon,
I have the clamp kits in stock but not the masters. Both are on back order.
I should have them some time next month.
Sincerely,
Jolene |
|
|
|
| Ask your question here: |
|
| Your email (so we can send you the answer): |
|
|
|
Event Photos
powered by