|
|
| Kawasaki Ninja EX250 Handlebar Risers (1986-2007) |
The risers are placed between the fork crown and the handlebars to raise the bars up 1 1/4" (38mm). This will help to relieve wrist and neck pain on long rides. Longer bolts are supplied. Requires no change of any control cables, wiring, or hoses.
Will NOT fit 2008 EX250. New product available soon, check site.
|
| |
| Item no. K108 |
| Today's Sale Price: $90.95 |
|
|
|
|
| Application Chart |
Diagrams |
Application
Notes |
|
| 2006 Kawasaki EX 250R Ninja |
|
|
| 2007 Kawasaki EX 250R Ninja |
|
|
| 1986 Kawasaki EX 250R Ninja E 1 |
|
|
| 1987 Kawasaki EX 250R Ninja E 2 |
|
|
| 1988 Kawasaki EX 250R Ninja F 2 |
|
|
| 1989 Kawasaki EX 250R Ninja F 3 |
|
|
| 1990 Kawasaki EX 250R Ninja F 4 |
|
|
| 1991 Kawasaki EX 250R Ninja F 5 |
|
|
| 1992 Kawasaki EX 250R Ninja F 6 |
|
|
| 1993 Kawasaki EX 250R Ninja F 7 |
|
|
| 1994 Kawasaki EX 250R Ninja F 8 |
|
|
| 1995 Kawasaki EX 250R Ninja F 9 |
|
|
| 1996 Kawasaki EX 250R Ninja F10 |
|
|
| 1997 Kawasaki EX 250R Ninja F11 |
|
|
| 1998 Kawasaki EX 250R Ninja F12 |
|
|
| 1999 Kawasaki EX 250R Ninja F13 |
|
|
| 2000 Kawasaki EX 250R Ninja F14 |
|
|
| 2001 Kawasaki EX 250R Ninja F15 |
|
|
| 2002 Kawasaki EX 250R Ninja F16 |
|
|
| 2003 Kawasaki EX 250R Ninja F17 |
|
|
| 2004 Kawasaki EX 250R Ninja F18 |
|
|
| 2005 Kawasaki EX 250R Ninja F19 |
|
|
|
|
|
|
|
|
|
|
|
|
| WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations. |
|
| The Q&A on this Product |
|
|
| QUESTION: Can you provide me with roaring toys handle bar riser for 08 Kawasaki ninja 250R? |
| ANSWER: |
|
| QUESTION: Will this fit the 2008 EX250? |
| ANSWER: We are currently working on the new EX250 risers. If all goes well, we should have them available in 3-4 weeks.
Thank you,
Scott-Genmar |
|
| QUESTION: scott,
Can the step be machined out to allow the fork tube to protrude all the way through??
(looking for a 1 1/4" min drop)
tnx. |
| ANSWER: Hi,
We could maching the step out but it would void all warranties and GenMar would not assume any liability for injury or loss of property. This would allow you to lower the front end at least 1 1/4".
Thanks again,
Scott-GenMar |
|
| QUESTION: will these allow me to raise the fork tubes in the tree?? I want to lower the bike 1 to 1 1/2 " in the front. |
| ANSWER: Hi,
The risers have a step built into the fork tube hole that will not allow the forks to go all the way through the riser. However, you will be able to lower the front end approx. 3/4".
Thanks for the inquiry,
Scott-GenMar |
|
|
|
| Ask your question here: |
|
| Your email (so we can send you the answer): |
|
|
|
Event Photos
powered by