|
| Woodcraft 50mm Clip-ons - 2`` Riser |
These clipons have a one inch rise over a conventional 50mm clipon. This rise is very similar to the stock rise on a GSXR handlebar. This clipon will give you the ability to have a race style clipon assembly with the option to get the bars up a little higher. This is a UNIVERSAL application - you must determine the fit and application of these riders to your motorcycle. Once installed in any way (screws tightened) they may NOT be returned. You may need to modify any of the following: Brake lines, Throttle cables, Clutch lines/cables, or electrical wiring harnesses. |
| |
| Item no. 12-3550 |
Retail: $179.99 (PLUS shipping) |
| Today's Sale Price: $169.95 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations. |
|
| The Q&A on this Product |
|
|
| QUESTION: Will this fit a 2007 yzf r6? if so how high of a rise can i have without it hitting and bodywork? |
| ANSWER: If you go to the Woodcraft website and click on any riser detail page there is a complete downloadable guide that walks you through the key things to look at on any motorcycle.
https://www.woodcraft-cfm.com/cgi-bin/commerce.cgi?preadd=action&key=12-15 |
|
| QUESTION: will this fit a 2006 gsxr 750 |
| ANSWER: We have not tested them on this motorcycle. The OEM forks on this bike have a taper 25mm below the stock triple clamp, so in order for the 50mm clipon base itself to fit you would need to raise the front of your bike at least 5mm. Many racers do this anyway to make the bike handle better.
As for the rise I have 2 comments: (1) The 1 tail description says this is a 1 inch rise over a standard clipon - that is wrong...it is a 2 inch rise (2)We have not tested a 2 inch rise on this model bike to know if there are any interference issues with the gauges. It may be best to give us a call so we can walk you through figuring it out...you can still order from 1 tail. |
|
| QUESTION: what kind of rise would i get over stock when installing these on a 07 1000rr? |
| ANSWER: First...1 tail has the wrong description here. They have a 2 inch rise over a conventional 50mm clipon. However, the OEM Honda clipon has about a 1.5 inch rise on it. So, this would give you about 1/2" of rise. This may not sound like a bunch, but sometimes a little bit of relief goes a long way. Also - a small change from stock is less likely to present installation issues.
We have not put them on an 07 CBR1000, so look at your OEM setup and be sure that there is room. If you have any question during an install we are always here to help. |
|
| QUESTION: do you have a picture of the 2" riser assembly? |
| ANSWER: If you go to www.woodcraft-cfm.com there are pictures of the clipons there. |
|
| QUESTION: will these fit a 1993 suzuki gsxr 750? are they 2 inches higher? |
| ANSWER: We have not worked with a 1993 yet. You need to determine if there is clearance by looking carefully at your motorcycle. Most GSXR's (since 1996 come from the factory with about a 1 inch rise, so this clipon would be 1 inch higher than stock (2 inches higher than a clipon with no rise) on those models. |
|
|
|
| Ask your question here: |
|
| Your email (so we can send you the answer): |
|
|
|
Event Photos
powered by WordPress e-commerce company