|
| Yamaha FJR1300 Handlebar Risers (06-08) |
The risers are placed between the fork crown and the handlebars to raise the bars up 1 1/4" (38mm). This will help to relieve wrist and neck pain on long rides. Requires no change of any control cables, wiring, or hoses.
|
| |
| Item no. Y203 |
| Today's Sale Price: $98.88 |
|
|
|
|
| Application Chart |
Diagrams |
Application
Notes |
|
| 2007 Yamaha FJR 1300 |
|
|
| 2008 Yamaha FJR 1300 |
|
|
| 2006 Yamaha FJR1300 |
|
|
|
|
|
|
|
|
|
|
|
|
| WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations. |
|
| The Q&A on this Product |
|
|
| QUESTION: it says thay raise the bars 1 1/4" but one of your answers says only 1".it's not a big deal i'm going to buy anyway. thanks |
| ANSWER: The Y-203 risers only raise the bars up 1". The 1 1/4" listing is a typo that I was unaware of.
Thank you,
Scott-Genmar |
|
| QUESTION: Just got the new 2009 fjr1300A,will these risers
fit this also? |
| ANSWER: Hi,
The Y-203 risers will fit the 09 FJR.
Thanks for the inquiry,
Scott-Genmar |
|
| QUESTION: I've just purchased these and installed them today. right side has a little movement in bar and beauty cover do not fit exactly like factory setup. They just kind of rest on top and don't quite set in properly, any insight to this problem? 07 FJR 1300a jim coury |
| ANSWER: Hi Jim,
As far as the movement goes, please recheck the torque on the mounting bolts. The handlebars should not have any play when torqued properly. Are the beauty covers bottoming out on the bolts? We usually don't have a problem with the covers not fitting correctly but it is possible that the bolts may be too long and not letting the covers go in place.
Thank you,
Scott-Genmar |
|
| QUESTION: do you ship to australia/ |
| ANSWER: |
|
| QUESTION: hi i just asked q question about cost of shipping to the UK you put the aswer is:- BLANK
you did not put in an answer |
| ANSWER: |
|
| QUESTION: how much is the shipping charge to send the handle bar risers Y203 to the UK and how long does it take |
| ANSWER: |
|
| QUESTION: on the 2008 fjr Handlebar Risers will can you still used the Using the two beauty covers that cover the handlebar mounting hardware? and you not?? |
| ANSWER: You will still use the two covers with the risers installed.
Thank you,
Scott-GenMar |
|
| QUESTION: Will these risers fit a 2007 FJR 1300 AE? The dealer who sold me the bike is not sure. |
| ANSWER: The Y-203 risers will fit the 07 FJR1300 AE.
Thanks for the inquiry,
Scott-GenMar |
|
| QUESTION: Do I have to remove the ignition from the triple clamp? There is no mention of this in the installation instructions, but the photos show the ignition removed.
Please clarify the height of the riser (conflicting information on your site). Is it 1-1/4 inches or 1 inch?
I'm also considering a helibar triple clamp. Can you compare the two products?
These questions relate to a 2008 FJR1300
|
| ANSWER: You will not have to remove the ignition from the triple clamp to install the Y-203 risers. We completely removed our triple-clamp from the bike for picture purposes only. The Y-203 risers are 1" tall. I haven't rode a new FJR with the Heli set-up so I don't have any information to compare the two products.
Thanks for the inquiry,
Scott-GenMar |
|
| QUESTION: I am in the UK, can you ship there? |
| ANSWER: Yes, we do ship to the UK daily.
Thank You,
Scott-genMar |
|
| QUESTION: will these risers fit on the 2008 FJR1300 model?
and how much is the shipping to hawaii? |
| ANSWER: The Y-203 risers will fit on the 08 FJR. |
|
| QUESTION: Your listing reads "Requires no change of any control cables," ect , is that for just for the 3/4" risers or for the 1" and 1 1/4" also. |
| ANSWER: We only carry one height riser for the new FJR1300. The risers are 1" and you can use all of your stock control cables.
Thank you,
Scott-GenMar |
|
| QUESTION: G'day Guys,
Im an accessories shop in Mooloolaba Qld Australia,Im chasing a pair of bar risers for a Yamaha FJR 1300 07 model could you please let me know price and availabilty for my customer.
Cheers Paul Sexton.
www.paul@madgear.com.au
www.madgear.com.au |
| ANSWER: |
|
| QUESTION: Is the pull back angle the same, or did you "flatten" it out some? I could live with the stock height if the angle were reduced some. |
| ANSWER: The riders do not change the stock angle of the bars. The bars can be rotated inward slightly but not upward. |
|
| QUESTION: Is your product available for shipping to Australia, or do you have an Australian distributor? |
| ANSWER: Our Y-203s are available and ready for shipment to Australia. We do not have an Australian distributor. |
|
| QUESTION: Will I still be able to change the angle of my bars? Are longer bolts supplied? |
| ANSWER: You will still be able to use the three stock settings for the handlebars. All the mounting hardware needed will be supplied. |
|
|
|
| Ask your question here: |
|
| Your email (so we can send you the answer): |
|
|
|
Event Photos
powered by